AP90T high frequency pressure sensor is used in military engineering, chemical explosion test, petroleum investigation and exploitation, petroleum well test, material, mechanics, civil engineering, geo-mechanics, traumatic medicine, hydraulic power mechanical test and other scientific tests.
AP90T high frequency pressure sensor is used in military engineering, chemical explosion test, petroleum investigation and exploitation, petroleum well test, material, mechanics, civil engineering, geo-mechanics, traumatic medicine, hydraulic power mechanical test and other scientific tests as well as modern instruments and meters, undistorted measurement of some frequently-changing dynamic pressure form, amplitude, and effective value with fast and steep pressure waveform rise shall be made. The high frequency pressure sensor has high intrinsic frequency, very short rise time, and wide and good response frequency band to ensure sufficient dynamic pressure measurement accuracy.
The high frequency pressure sensor is specially designed for this purpose. The high frequency pressure sensor adopts high performance chip of a foreign company, using micro machining technology to enable small effective dimensions and high intrinsic frequency of the integrated silicon chip. The high frequency pressure sensor boasts good elastic mechanics characteristics and its comprehensive performance is better than that of piezoelectric dynamic pressure sensor. Thus, high frequency pressure sensor is ideal for dynamic pressure measurement.
* Stainless steel enclosure, with excellent corrosion resistance
* Wide pressure measuring range
* Intrinsic frequency up to 2MHz
* Stable working
* Strong interference immunity
* Genuine imported module with stable performance
* Small dimensions, light weight, a variety of types and high cost performance
* Wide range of measured medium
*Petroleum investigation and exploitation and petroleum well test
*Chemical explosion test
*Civil engineering
*Geo-mechanics
*Traumatic medicine
*Military engineering
*Hydraulic power mechanical test and other scientific tests
*Mechanics
Measuring range | -100KPa~0~1KPa…20KPa…100MPa | |||
Overload capacity | Two times FS pressure ((1.1 times FS pressure for 100MPa product) | |||
Pressure type | Gauge pressure or absolute pressure | |||
Measured medium | Gas or liquid compatible with 316 stainless steel | |||
Overall accuracy | ±0.1 %FS | ±0.25%FS | ±0.5%FS | |
Intrinsic frequency | 150KHz~700KHz | 500KHz~1MHz | 1MHz~2MHz | |
Band width of transducer | 0~1KHz~3KHz | 0~20KHz | 0~200KHz | |
Rise time | 0~0.2mS~75μS | 0~12μS | 0~1μS | |
Long-term stability | Typical: ±0.1%FS/ year | Maximum: ±0.2%FS/ year | ||
Operating temperature | -40℃~85℃ generally | -10℃~250℃ specially | ||
Zero point temperature drift | Typical: ±0.02%FS/℃ | Maximum: ±0.05%FS/℃ | ||
Sensitivity temperature drift | Typical:±0.02%FS/℃ | Maximum: ±0.05%FS/℃ | ||
Range of power supply | 12~36VDC (24VDC generally) | ±15VDC standard switching power supply | ||
Signal output | 4~20mA / 1~5 V DC / 0~5V DC | |||
Load resistance | ≤(U-12)/0.02Ω | |||
Enclosure protection degree | Plug-in type (IP65); cable type (IP67) | |||
Vibration error | ≤±0.01%FS(Axles X, Y, Z,200Hz/g) | |||
Port and enclosure | Stainless steel 1Cr18Ni9Ti | |||
O-ring | Fluo rubber | |||
Sensor diaphragm | Stainless steel 316L or mono – crystalline silicon | |||
Safe explosion- proof | Ex ia IICT6 | |||
Insulation resistance | 100MΩ,500V DC | |||
Resolution | Infinite small (theoretical) 1 / 100000 (general) |
AP90T | High Frequency Dynamic Pressure Sensor | ||||||
Code | Pressure type | ||||||
G | Gauge pressure ( G, may not be indicated) | ||||||
A | Absolute pressure (A) | ||||||
Range | ( 0~ X KPa or MPa) Measuring Range | ||||||
Code | Band width of transducer | ||||||
H1 | 0~1KHz~3KHz | ||||||
H2 | 0~20KHz | ||||||
H3 | 0~200KHz | ||||||
Code | Overall accuracy (linear + repeatability + lagging) | ||||||
1 | ±0.5%FS | ||||||
2 | ±0.25%FS | ||||||
3 | ±0.1%FS | ||||||
Code | Signal Output | ||||||
A1 | 4~20mA | ||||||
V1 | 1~5V DC | ||||||
V2 | 0~5V DC | ||||||
Code | Additional functions | ||||||
F1 | M20x1.5 external thread | ||||||
F2 | G1/4 external thread | ||||||
F0 | Special | ||||||
W1 | Cable type (IP67, 2m) | ||||||
W2 | Socket type (IP65, DIN 43650) | ||||||
P | Flush diaphragm | ||||||
E | Intrinsically safe explosion-proof type Ex iaIICT5 | ||||||
T1 | Free field (specially used for blasting) | ||||||
T2 | High – temperature resistant type: Up to 250 ℃ for balanced use,Up to 2000 ℃ for transient use | ||||||
AP90T(0~500KPa)—H1 —1 —V2 —F1 —W1 —E – T2 High Frequency Dynamic Pressure Sensor |